ANCEL All System Heavy Duty Truck Diagnostic Tool DPF Scan Tool Fit For Cummins

 HD3300 Function advantages

●  DPF Regeneration fit for :Fit For Cummins, Fit For Detroit, Fit For Caterpillar, Fit For International , Fit For Volvo, Fit For Paccar, Fit For Isuzu, Fit For Fuso

DPF Regeneration (Fit for Cummins, Fit for Detroit, Fit for Caterpillar, Fit for International, Fit for Volvo, Fit for Paccar, Fit for Isuzu, Fit for Fuso​)

DPF Regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such us high temperature heating conbustion, fuel additive or catalyst reduce PM ignition conbustion) to stabilize the filter perfornance. ​An unmaintained DPF runs your vehicles unnecessarily hard and less efficient. With regular DPF maintenance, you can save lots of dollars and time by getting your DPF cleaned, restore your DPF to nearly new! Increased Fuel Economy up to 5%. Avoid costly replacement of the filters. Lower Overall Maintenance Costs.

DPF regeneration may be performed in the following cases:

(a) The exhaust back pressure sensor is replaced.

​​(b) The PM trap is removed or replaced.

​(c) The fuel additive nozzle is removed or replaced.​

(d) The cataytic oxidizer is removed or replaced.

​(e) The DPF regeneration MIL is on and maintenance is performed.

​​(f) The DPF regeneration control module is replaced.

DPF regeneration ensures that the vehicle state meets the following requirements:

1. First of all, when dpf is regenerated, the vehicle needs to ensure that the vehicle speed is 0, and the brake pedal, clutch pedal and accelerator pedal of the vehicle are in a normal relaxed state, that is to say, the accelerator, brake and clutch pedal of the vehicle are not stepped on.

2. In addition, the gear of the car needs to be kept in the neutral position, and the dpf regeneration function cannot be turned on with gear. At the same time, the hand brake of the car should be tightened.

3. In the process of starting the regeneration function of automobile dpf, it is also necessary to ensure that the engine of the automobile is always in an idle state, and the temperature of the automobile water tank is best kept above 40 degrees Celsius.

4. Engine running at idle speed, and water temperature should be higher than 80 Celse Degree. 

5. Coolant temperature is higher than 60″C Degree;  Fuel temperature is lower than 70″C degree; 

The above conditions are necessary for the dpf regeneration process. If any of the above conditions are not met, the dpf function of the car will not work normally at this time.

●Maintenance Oil Service light reset:Isuzu, Fuso

If the car owner replaced the relevant parts, but does not reset maintenance lamp, it will not affect the performance of the vehicle, but it will bring trouble to the next replacement of the car parts: it is impossible to know exactly when the new parts are used. The intelligent maintenance system CBS permanently monitors oil levels and the degree of wear and tear on individual components of your vehicle. It also checks the time/mileage recommendations for fixed services and it analyses this data and tells you when a service is next due.

● Support OBDII, Diesel OBD standard protocol, and has covered the latest J27145 protocol;

● Support Cummins automatic diagnosis (Smart Detect);

●Simulate and DEMO simulation function; (refer to CAT)

●Support reading, clearing and reading data stream functions;

●Support a variety of test methods; (Users can choose to test by year, model system, or test by model. If it is the Diesel OBD menu, it can also support Fast Scan or Complete Scan.)

Heavy Duty Truck for multi- system scan Support 

American
for Freightliner, for IWC, for Kenworth, for Peterbilt, for Sterling, etc…

Asian
for Hino, for Fuso, for Isuzu, for UD Truck, for Hyundai Truck, for Ashok Leyland, etc…

Europe
for Mercedes-Benz commercial vehicles,for Man, for Iveco, for Renault, for Duff, for Scania, for Kamas and so on…

China
for Dongfeng Commercial Vehicle, for FAW Jiefang, for China National Heavy Duty Truck, for Futian Commercial Vehicle, for Shaanxi Heavy Duty Truck and more

Full OBDII Engine Function Check for 12V vehicles

12V Passenger vehicles Support

Car (US Domestic) after 1998: For Buick, For Cadillac,For Chevrolet, For Chrysler, For Dodge, For Ford, For GM, For GMC,For Lincoln,For Jaguar,For Jeep, ForPontiac, For Saturn

Car (Europe) after 2002: For Audi, For Bentley, For BMW, For Fiat, For Jaguar, For Land Rover, For Mercedes Benz, For Mini, For Porsche,For SAAB, For Smart,For Sprinter,For Volvo,For VW

Car (Asia) after 2004: For Acura,For Daewood,For Honda,For Hyundai,For Infiniti, For Isuzu,For Kia,For Lexus,For Mazda,For Mitshubishi,For Nissan, For Scion,For Subaru,For Suzuki,For Toyota;

Pickup (or Van):For Silverado,For Corolado,For Ford (F150-750),For Ford E-series,For Dodge RM 1500-5500,For GMC,For Nissan Frontier, For Toyota

For Truck(12V/24V):
For Freightliner,For Kenworth,For Peterbilt,For International,For Mack,For Ford,For HD Volvo

Please enter the menu【OBD-II】 if you want to diagnostic12V cars. Please kindly note that you should enter menu 【Diesel OBD】 if you want to diagnose heavy duty trucks.

The following is an operation description of these two connection modes:

1) Connection of standard OBD-II interface – The vehicle only needs to use the integrated main test line OBD connector, and no other connectors are needed.

2) Connection of Diesel 6/9 PIN interface – Vehicles need to connect the main test line with the corresponding special connector.

This function mainly measures the voltage of 16 PIN of OBD diagnostic interface, and judges the pin position of K- line and CAN line. After connecting the OBD interface of the vehicle, click the main interface “Tools” to select pin detection. The program automatically measures the 16pin voltage of the OBD diagnosis interface, and judges the pin position of K-line and can line.

Note: The test requires ECU no response, please ask the customer to check whether the diagnostic interface has voltage

Support Print & Share Report