2024 LAUNCH CRP123I V2.0 Car OBD2 Scanner Diagnostic Tool DPF Brake ABS Reset

● 4 Systems Diagnostic Scan: Read/Clear fault codes and turn off the warning light of Engine /Transmission / ABS /SRS System.

● 7 Reset Functions : SAS Reset / Oil Service Reset / ETC Reset / EPB Brake Reset / DPF Regen / BMS Reset

● Full OBDII Functions: To Pass the Emission/Smog Test
● AUTO-VIN: only supports some vehicles, some vehicles are not compatible. If your vehicle can not use this function, please try to select the vehicle software manually.
● 4 in 1 live data stream in graph: (such as engine speed, transmission temperature, etc.), retrieve vehicle information and switch the MIL.
● Lifetime Free Update: one-click update via WiFi, fixes bugs and updates vehicle manufacturers to 2022/ 2023 models.

● Added Shopping “Mall”: in Mall , it can subscribe reset function and Full system of the car , each one is USD$49.95/pc .
● Hardware: Android 8.1 Operation System, 5” Touch Screen, 6100mAh Battery,2GB+32GB Memory

 

4 Systems Diagnosis (Lifetime Free Use )

Engine System:
The diagnostic tool can help detect the engine ignition, fuel injection, air and fuel ratio, and exhaust emission conditions in Engine system to enhance vehicle performance, save energy and reduce exhaust emission.
Transmission System:
It makes great sense in the safe driving when your car is slipping or difficult to shift. This diagnostic scanner can figure the problems out via reading codes in the Transmission system, or check the health status via live data viewing.
ABS System:
Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you.
SRS Airbag System:
SRS, safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status.

1> Oil Reset Service
This function enables you to reset the oil service for the engine oil life system,which calculates an optimal oil life change interval depending on the vehicle driving conditions and weather events.
lt needs to be performed in the following cases:
1. lf the service lamp is on, run car diagnostics first for troubleshooting.Afterthat, reset the driving mileage or driving time, so as to turn off the servicelamp and enable a new driving cycle.
2. lf the service lamp is not on, but you have changed the engine oil or electric
appliances that monitor oil life, you need to reset the service lamp.

2> Electronic Parking Brake Reset
This function enables you to reset the brake pad after replacing the brake pad.lt needs to be performed in the following cases:
1.The brake pad and brake pad wear sensor are replaced.
2.The brake pad indicator lamp is on.
3.The brake pad sensor circuit is short, which is recovered.4.The servo motor is replaced.

3> ABS Bleeding
This function allows you to perform various bi-directional tests to check theoperating conditions of Anti-lock Braking System(ABS).
lt needs to be performed in the following cases:
1. When the ABS contains air.
2. When the ABS computer, ABS pump, brake master cylinder, brake cylinder,brake line, or brake fluid is replaced.

4> Battery Maintenance System Reset
This function enables you to perform a resetting operation on the monitoringunit of vehicle battery, in which the original low battery fault information will becleared and battery matching will be done.
lt needs to be performed in the following cases:1. The main battery is replaced.
2. The battery monitoring sensor is replaced.

5> Diesel Particulate Filter (DPF) Regeneration
This function enables you to clear PM(Particulate Matter) from the DPF filterthrough continuous combustion oxidation mode (such as high temperatureheating combustion,fuel additive or catalyst reduce PM ignition combustion)to stabilize the filter performance.
lt needs to be performed in the following cases:
1. The exhaust back pressure sensor is replaced.
2. The PM trap is removed or replaced.
3. The fuel additive nozzle is removed or replaced.
4. The catalytic oxidizer is removed or replaced.
5. The DPF regeneration MlL is on and maintenance is performed.
6. The DPF regeneration control module is replaced.

6> Electronic Throttle Position Reset
This function enables you to make initial settings to throttle actuators andreturns the learned values stored on ECU to the default state. Doing so canaccurately control the actions of regulating throttle (or idle engine) to adjust theamount of air intake.

7> Steering Angle Calibration
This function enables you to reset the steering angle,after replacing thesteering angle position sensor,replacing steering mechanical parts (such assteering gearbox,steering column, end tie rod, steering knuckie), performingfour-wheel alignment, or recovering car body.
To reset the steering angle, first find the relative zero point position for thecar to drive in straight line. Taking this position as reference,the ECU cancalculate the accurate angle for left and right steering.

 

10 EOBD OBDII Functions(Emission/SmogTest Fit1996-Now)
$01 – Request Current Powertrain Diagnostic Data
$02 – Request Powertrain Freeze Frame Data
$03 – Request Emission-Related Diagnostic Trouble Codes
$04 – Clear/Reset Emission-Related Diagnostic Information
$05 – Request Oxygen Sensor Monitoring Test Results
$06 – Request On-Board Monitoring Test Results for Specific Monitored Systems
$07 – Request Emission-Related Diagnostic Trouble Codes Detected During Current or Last Completed Driving Cycle
$08 – Request Control of On-Board System Test or Component
$09 – Request Vehicle Information
$0A – Request Emission-Related Diagnostic Trouble Codes with Permanent Status

 

Quick VIN Identification
The CRP123I V2.0 is an easy-to-use scanner aiming at helping you solve automotive issues quickly and accurately. In addition to manually selecting the vehicle information like year, make, model, and VIN, you can quickly access the system via AutoDetect for VIN acquisition.
Real Time Battery Voltage Graphing
Check the battery status in real time and eliminate the most easily overlooked battery problems
Live Data Stream Analyse in Graph
The launch scanner CRP123I V2.0 shows you live sensors data and provides data graphing for intuitive diagnostics and monitoring your vehicle performance, help customers to better analyze the abnormal parameter.
Date Record & Playback
Another great feature about this automotive diagnostic scanner is that it would allow you to view the Live Data Stream, and to record the data in Waveform.   This would save you the hassle of reading through and digesting all the information which is being presented to you.   You can even playback these data, for better analysis and rectification as well as future use.
Google DTC Inside
After you get the diagnosis results, quickly get the maintenance information through the built-in Google DTC system. Professional, efficient connection of Internet mass information, easy to improve hands-on ability
Share Report via Wi-Fi & print Report
Rather than taking the additional hassle, with this LAUNCH scanner, you would easily be able to share the diagnostics report to your clients or technicians via Wi-Fi.  They would take a look at the full, clear, and accurate diagnostic report, and then understand what would need to be done.  No more Googling unreliable fixes that would waste your energy.

 

Supported Car Brands

The code reader has an expanded coverage for more than 57 suitable vehicle makes to access the engine, AT, ABS and airbag

 

LCD Screen: 5 Inch Touch Screen
Operation System: Android 8.1
Battery: 6100mAh Battery
RAM+ROM: 2GB+32GB
OBD II interface input voltage: 9V~18V DC input voltage: 5V
Connection:standard 16 PIN OBD diagnostic interface
Working temperature:-10°C to 50°C
Storage ambient temperature:-20°C to 70°C
Dimension:228*125*34.5(mm)
Weight:<565g

1 x Creader Professional 123i v2.0 handset

1 x OBD II diagnostic cable

1 x DC 5V charging cable

1 x User manual

1 x Carrying bag